Modeling and Simulation
A. Das; N. Azimi
Abstract
This research presents the performance of bladeless wind turbines. It also familiarizes readers with the phenomenon of eddy current, which serves as the foundation for bladeless turbines. In this direction, these kinds of bladeless turbines have been designed, modeled, and simulated. Firstly, a two-dimensional ...
Read More
This research presents the performance of bladeless wind turbines. It also familiarizes readers with the phenomenon of eddy current, which serves as the foundation for bladeless turbines. In this direction, these kinds of bladeless turbines have been designed, modeled, and simulated. Firstly, a two-dimensional vibrational movement of the cylinder with a natural frequency of 2 Hz was modeled at Re = 51000. Additionally, it was noted that the values of the displacement amplitude, and lift coefficient are in the 0.8, and 1-1.5 ranges, respectively. After that, using 2D simulation, the impacts of two different geometries, horizontal and vertical ellipsoids, on displacement amplitude are examined. Investigations were conducted on important factors such as lift coefficients and displacement amplitude, as well as the vortex flow pattern formed behind these shapes. It was discovered that the vertical ellipsoid shape had the maximum values for the height of the displacement amplitude, and lift coefficient. The most important factor influencing this type of geometry's performance was examined in the following, namely the dimensionless Reynolds number, which ranges from 15000 to 90000. It was determined that the intended geometry exhibits a larger displacement response as the Reynolds number increases.
Energy
H. Amiri; A. Babapoor; M. Fallahi-Samberan; N. Azimi; A. Hadidi
Abstract
Current research has simulated polymer oxide/metal oxide nanofibers (nanocomposites) through the COMSOL Multiphysics software. The oil was placed inside a cylindrical tank covered with a thin layer of phase change material nanocomposites. A combination of polyethylene glycol (PEG) as a the phase change ...
Read More
Current research has simulated polymer oxide/metal oxide nanofibers (nanocomposites) through the COMSOL Multiphysics software. The oil was placed inside a cylindrical tank covered with a thin layer of phase change material nanocomposites. A combination of polyethylene glycol (PEG) as a the phase change material (PCM) and polyamide 6 (PA6) as a support matrix for nanofibers were used. The effect of some parameters such as the type of metal oxide nanoparticles (Al2O3, Fe2O3, TiO2, and CuO), the ratio of metal oxide to polymer (2% and 8% by weight), and time (600 and 4800 s) on some thermophysical properties such as changes in temperature, density and thermal conductivity were investigated. The simulation results showed that the most suitable system for thermal management is related to the presence of nanoparticles and PCM with the highest weight percentage. It was also found that the use of the nanofibers of phase change materials is very effective in improving thermal management and temperature control. As a result, they can be used as suitable materials for storing and transferring energy. The addition of 8% nanoparticles led to a 22.5% increase in thermal conductivity. Also, by providing the same initial and boundary conditions for all cases, the amount of melting in the presence of nanoparticles with a high percentage (8%) was higher than the with a low percentage (2%). As a result, the addition of nanoparticles to increase the melting rate can be very useful for various heat management purposes such as energy storage.
Modeling and Simulation
p. Amjadian; N. Almasi; N. Azimi
Abstract
In this paper, CFD modeling of ferrofluid convection heat transfer in a micromixer with static magnetic field (SMF) and rotating magnetic field (RMF) is investigated. Applying a magnetic field and the existence of magnetic nanoparticles lead to the creation of transverse vortices in the micromixers by ...
Read More
In this paper, CFD modeling of ferrofluid convection heat transfer in a micromixer with static magnetic field (SMF) and rotating magnetic field (RMF) is investigated. Applying a magnetic field and the existence of magnetic nanoparticles lead to the creation of transverse vortices in the micromixers by movement of nanoparticles, that improves heat transfer. There is a cylindrical pit in the microcmixer with heat source that is applied to its bottom wall. Top wall of the pit is adjacent to a fixed permanent magnet, which creates the SMF. CFD modeling first is done for heat transfer process in the micromixer in the absence of the magnetic field. Secondly, simultaneous effect of the SMF and magnetic nanoparticles on the flow pattern and heat transfer rate of ferrofluid is evaluated. Results showed that ferrofluid leads to the improvement of the heat transfer rate compared to pure water. The secondary flows induced by nanoparticles’ motion toward SMF decreases the velocity in the area of application of the magnetic field, so the heat transfer coefficient decreases. But, in the case of RMF, applying the magnetic field causes the nanoparticles to rotate inside the pit, which leads to an increase in the heat transfer coefficient. CFD results of heat transfer coefficient are compared with experimental results in a reliable reference and acceptable agreement between them is observed.
N. Heidari; M. Rahimi; N. Azimi
Abstract
Wind energy is used to rotate a magnetic turbine in order to remove heat from the surface of a photovoltaic (PV) panel. A three-bladed turbine, which rotates with wind energy, has rotational motion underneath the studied PV panel in order to move Magnetic Nano-Particles (MNPs). In addition, effects of ...
Read More
Wind energy is used to rotate a magnetic turbine in order to remove heat from the surface of a photovoltaic (PV) panel. A three-bladed turbine, which rotates with wind energy, has rotational motion underneath the studied PV panel in order to move Magnetic Nano-Particles (MNPs). In addition, effects of the magnetic field strength (B=450-830 mT), rotational velocity of the magnetic turbine (ω), and the concentration of MNPs (ϕ) on the heat removal from the PV panel area were investigated. Results showed that heat removal from PV panel was intensified by motion of pinned MNPs in the ferrofluid via the exerted external force of magnetic field. Concurrent application of available magnetic field along with ferrofluid led to 7.6-24 % temperature reduction for a PV panel. Furthermore, the produced electrical energy of the PV panel was augmented between 2.55-3.13 W depending on ϕ, ω, and B. Moreover, the impact of ω on cooling performance was also investigated, and a significant enhancement to generated power was observed. Eventually, the maximum amount of the produced power (3.13 W), maximum power enhancement percentage (32.63 %), and thermal efficiency (24 %) were achieved for B=830 mT, ω=50 cycles/min, and ϕ=0.05 (w/v).