Volume 21 (2024)
Volume 20 (2023)
Volume 18 (2021)
Volume 17 (2020)
Volume 16 (2019)
Volume 15 (2018)
Volume 14 (2017)
Volume 13 (2016)
Volume 12 (2015)
Volume 11 (2014)
Volume 10 (2013)
Volume 9 (2012)
Volume 8 (2011)
Volume 7 (2010)
Volume 6 (2009)
Volume 5 (2008)
Volume 4 (2007)
Volume 3 (2006)
Volume 2 (2005)
Volume 1 (2004)
Investigation. effect. of mixed. matrix. membranes’. structural. parameters. on their. effective. gaseous. penetrant. diffusion. ratio using. CFD tools

M. Morovat; O. Bakhtiari

Volume 19, Issue 4 , December 2022, Pages 3-19

https://doi.org/10.22034/ijche.2023.384122.1475

Abstract
  Ability and compatibility of the membrane processes for gas separation are evaluated by their membranes’ permeability and selectivity where both have been tried to enhance in promising membrane generation of mixed matrix membranes (MMMs). In the current study, two- and three-dimensional models ...  Read More

Regular Article Modeling and Simulation
3D simulation of carbon monoxide purification with CuCl(7.0)/AC by pressure swing adsorption process

P. Sharafi; E. Salehi; H.R Sanaeepur; A. Ebadi Amooghin

Volume 19, Issue 4 , December 2022, Pages 20-37

https://doi.org/10.22034/ijche.2023.379083.1469

Abstract
  In this work, the separation of carbon monoxide (CO) from a synthesis gas (syngas) mixture was modeled. It was considered a copper-based adsorbent consisting of cuprous chloride (CuCl) on an activated carbon (AC) support (CuCl/AC) in a pressure swing adsorption (PSA) process. First, the adsorption of ...  Read More

Regular Article Process Control and Engineering, Process Safety, HSE
Investigating Effective Parameters in Hazardous Areas of City Gas Station (CGS) , Through Modeling Using PHAST Software

V. zaroushani; H. mirzakhani; F. khajehnasiri

Volume 19, Issue 4 , December 2022, Pages 38-51

https://doi.org/10.22034/ijche.2023.369154.1463

Abstract
  Natural gas (NG) is one of the cleanest and safest sources of energy transmitted in a high pressure that must be reduced before entering City Gas Station (CGS). Identifying the effective parameters in creating the hazardous areas of CGS is essential to crisis and management. This study using PHAST version ...  Read More

Regular Article Process Control and Engineering, Process Safety, HSE
Plantwide Control Structure of the Diethyl Oxalate Process Concerning: Safety and Process Improvement

H. Bagheri; M. M Khalilipour; J. Sadeghi

Volume 19, Issue 4 , December 2022, Pages 52-75

https://doi.org/10.22034/ijche.2023.355995.1455

Abstract
  During the regeneration-coupling process, a novel, plantwide control framework for the diethyl oxalate production unit is provided in this article. This study's benefit is that it uses process improvements that do not possess the intricacy and expense of the two prior structures described by Zhu and ...  Read More

Regular Article Materials synthesize and production
Pilot Plant Scale Interesterification of Special Fat Blends to Prepare Zero-Trans Margarine: Monitoring the Fatty Acids content and Physicochemical Properties

N. Shahgholian; M. Jalilpiran

Volume 19, Issue 4 , December 2022, Pages 76-94

https://doi.org/10.22034/ijche.2023.382122.1473

Abstract
  The chemical interesterification (CIE) process is a promising approach to modifying and improving oils and fat structure. In this study, CIE of fully hydrogenated soybean oil (FHSO) and sunflower oil (SFO) was performed. Different initial blends with various mass ratios of 20-45% FHSO (coded as S1, S2, ...  Read More

Regular Article Modeling and Simulation
Improving the performance of a two-phase ejector using genetic algorithm based on secondary fluid entrainment rate

M. Moghadasi; M. Moraveji; O. Alizadeh

Volume 19, Issue 4 , December 2022, Pages 95-109

https://doi.org/10.22034/ijche.2023.390350.1488

Abstract
  Ejectors offer a cost-effective and practical solution for recovering flare gases, thereby reducing greenhouse gases. Improving the entrainment rate of the secondary fluid can enhance ejector performance. The objective of this research is to identify the optimal ejector geometry to maximize the absorption ...  Read More